Industrial Epoxy Primer - 100% Solids

For Concrete and Wood

Product #3899

Product Description

Epoxy.com Product #3899 is a 2-component, low viscosity, 100% solids, epoxy primer for concrete and wooden substrates.

DESCRIPTION

Product #3301 is a 100% solids low viscosity primer which can be used under a variety of Epoxy.com Coating and Flooring Systems.

ADVANTAGES

• Low viscosity - exceptional flow characteristics
• High Strength

APPLICATION PROCEDURES

Surface Preparation for Epoxy Injection

Surface must be clean and sound. Interfaces of cracks must be free of dirt, laitance, grease, curing compounds and other foreign matter.

Epoxy Mixing Directions

Temperature of Product #3899 must be 60°F. or above at time of mixing. Stir each component separately before blending. Best if used in an automatic binary mixing system. If mixed manually mix two parts by volume of Part A with one part by volume of B for three minutes with a low-speed electric drill motor equipped with a mixing paddle.

Application Epoxy Primer

Apply by brush, roller or squeegy at a rate of 250-300 SF per square foot.

For more information consult Epoxy.com technical service department.

Limitations of Epoxy Injection Resin

Minimum substrate temperature must be 50° F.

Cleaning Epoxy Injection Resin from Tools

All tools and equipment should be cleaned before the system gels. Use methyl ethyl ketone or any lacquer solvent.

Environment & Health

This is a solvent free and Nonyl Phenol free product, and practically odorless during application. Follow the appropriate Occupational Health and Safety guidelines applicable to the location where the application is undertaken. For more information, please refer to the safety datasheets for the individual components.

Ratio of Components

2 parts of component A are mixed with 1 part of component B, by volume.

Add Hardener B to Base A. Mix with slow speed drill and appropriate mixing paddle taking care not to entrain air. May also be mixed by appropriate static mix tube.

Application Temperature

The recommended substrate temperature is 60° - 80°F, but no less than 50°F.

Application Time/Pot Life

Mixed product should be used within 40 minutes at a temperature of 70°F. At higher temperatures the application time is shorter.

Curing Time (at 70°F)

Approximately 12 hours. The product is fully hardened after 5 - 7 days.

Colors

Transparent

Finish

Gloss

Solids Content

Approx. 100 %

VOC

12 g/l

Density

Component A approx.- 9.30 lbs/gal (1.12 kg/l)

Component B approx. - 8.60 lbs/gal (1.03 kg/l)

Mixed approx. - 9.10 lbs/gal (1.09 kg/l)

Storage

12 months in unopened pack. Storage temperature between 40°F and 100°F. Protect from weather and moisture / contaminant ingress (tightly sealed to prevent air infiltration, and exfiltration).

Packaging

The product is delivered A+B in the following packs:

Physical Properties

Further Information

If you would like additional information, please Epoxy.com Technical Support Department

Disclaimer

Any recommendation or suggestion relating to the use of the products sold by Epoxy,com whether in its technical literature, or in response to a specific enquiry, or otherwise, is based upon data believed to be reliable, however the products and information are intended for use by Customers having requisite skill and know-how in the industry and therefore it is for the Customer to satisfy itself of the suitability of the products for its own particular use and it shall be deemed that the Customer has done so at its sole discretion and risk.

Proper mixing and installation is critical to the optimal success of all products.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
A Vermont Corporation
USA

We have products that have passed the test of time as well as the best new Systems available today.

Since 1980 - Over 45 years of the highest quality products

Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time)

Closed for lunch from 12Noon to 1PM

321-206-1833  Customer Service - Ordering and Order Status
Katey Lambert-Fontaine - Vice President & Chief Operations Officer
katey@epoxy.com

352-533-2167  Technical Support
Norm Lambert - President & Technical Support Director
info@epoxy.com

Debby Lambert, Co-Founder and Strategic Planning

Website: www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service - 1-800-633-8253

[Home] [Catalog of Products] [MSDS in Acrobat Format] [Online Ordering Authorization Form]