|
||
| [Contact Us] | ||
Epoxy Chip Flooring Base Coating
High-Build Coating100% Solids
Epoxy.com Product #315BC
GENERAL DESCRIPTION
Epoxy.com Product #315BC High-Build Polymeric Coating is a two component, 100% solids polymeric Hi-Build polymeric coating used for high foot and light forklift traffic areas where abrasion resistance is required; for protection against mild corrosion; and as a decorative waterproof coating for walls, floors, tanks, pools etc. Also used as a base coat for Epoxy.com Chip Flooring System.
ADVANTAGES
- Moisture Insensitive
- Ceramic like finish
- Sprayable
- Solvent Free
- Waterproof
- Extremely Durable
- Chemical Resistant
SURFACE PREPARATION
Surface to receive Epoxy.com Product #315BC High-Build Polymeric Coating must be clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, or mechanical abrasion. Remove water and dust from all surfaces with an oil free blast immediately prior to application.
MIXING INSTRUCTIONS
Temperature of Epoxy.com Product #315BC High-Build Polymeric Coating (normal cure) must be 50° F or above at time of mixing. Stir each component separately before blending. Mix two parts by volume of Part A with one part by volume of Part B for three minutes with a low speed electric drill motor equipped with a mixing paddle.
APPLICATION
ApplyEpoxy.com Product #315BC High-Build Polymeric Coating with a roller, brush, or spray equipment. When not used as part of the 315 Chip Flooring System, 2 coats are recommended. Thickness per coat should be 7-10 mils. Seven days cure time is required to reach maximum chemical resistance. When installing over concrete Product #899 or Product #203 Primer is recommended.
LIMITATIONS
DO NOT apply Epoxy.com Product #315BC High-Build Polymeric Coating at temperatures below 50° F. Surface must be dry.
SAFETY PRECAUTIONS
Prolonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves.
CLEANING
All tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent
APPLICATION PROPERTIES @77°F |
||
| Mix Ratio | 2:1 By Volume | |
| Viscosity (mixed) | 950 CPS | |
| Pot Life (200 gr.) in minutes @70° F. | 30-40(normal cure) | |
| Set Time in Hours @ 70° F. | 10-12 (normal cure) | |
| Initial Cure | 24 Hours | |
| Final Cure | 5 Days | |
| Packaging Unit Size | 3 gallon units (2 gallons of "A" + 1 gallon of "B" | |
| Standard Colors | White, Light Gray, Dark Gray, Taupe, Sand, Old Gold, Mocha, Brick Red, Slate Blue, Colonial Green, Deep Blue, Black, Safety Yellow |
|
Click the picture
of color card below for a larger version of this picture
of the color chart.
Please note: The picture to the right is a photographic reproduction of the color card for this product. The photo reproduction process and your monitor and/or printer will change these colors. This chart is to give you an idea of the colors available and not intended for critical color selections.
Material Certification of LEED Requirements
Epoxy.com a division of Epoxy Systems, Inc. certifies that Epoxy.com meet or exceed LEED requirements as summarized below:
LEED Credit IE 4.2:
Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to LEED IEQ 4.2 Indoor Emitting Materials Credit. Refer to the individual product component technical data sheets and MSDS for further information.
Other customers who visited this page also visited:
- Epoxy.com Product #1 - All Purpose Epoxy Coatig
- Epoxy.com Product #1W - Wall Grade Version of Epoxy.com Product #1
- Epoxy.com Product #2 - Chemical Resistant Epoxy coating.
- Epoxy.com Product #633 - Epoxy Novolac Coating - extremely chemical resistant
- OSVX464 - High Temperature Epoxy Coating.
- Epoxy.com Chip Flooring System
- Epoxy.com Coatings Page.
Proper mixing and installation is critical to the optimal success of all products. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have.
For more information please contact:
Epoxy.com
A Division of Epoxy Systems, Inc
A Vermont Corporation
USA
We have products that have passed the test of time as well as the best new Systems available today.
Since 1980 - Over 45 years of the highest quality products
Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time)
Closed for lunch from 12Noon to 1PM
321-206-1833 Customer Service - Ordering and Order Status
Katey Lambert-Fontaine - Vice President & Chief Operations Officer
katey@epoxy.com
352-533-2167 Technical Support
Norm Lambert - President & Technical Support Director
info@epoxy.com
Debby Lambert, Co-Founder and Strategic Planning
Website: www.epoxy.com
24 hour Hazmat Emergency Telephone Response Service - 1-800-633-8253
[Home] [Catalog of Products] [MSDS in Acrobat Format] [Online Ordering Authorization Form]