|
||
| [Contact Us] | ||
URETHANE COATING/SEALER GLOSS
EPOXY.COM PRODUCT #442
Description
EPOXY.COM PRODUCT #442 is a two component water- based aliphatic (non-yellowing) polyurethane. Product #442 is free of the health and environmental problems normally found in solvent-based urethanes, while maintaining excellent performance properties. Product #442 is also available in an ESD formulation which must be applied over a base coat of Epoxy.com Conductive Epoxy.
EPOXY.COM PRODUCT #442 polyurethane provides a gloss finish. Product #442 has good chemical, stain, and mar resistance. In addition, it's easy to clean and has excellent color retention under heavy foot traffic.
EPOXY.COM PRODUCT #442 is a high performance coating for use in a variety of seamless floor and wall coating systems. Product #442 eliminates the strong solvent odor normally associated with high performance materials. It's ideal for topcoats and finishes that require high abrasion resistance. Typical application areas are clean rooms, hospitals, pharmaceutical facilities, stained concrete, wood floors, and as a seal coat for most Epoxy.com floor and wall coating systems.
ADVANTAGES
- Low VOC
- Low Odor
- Fast Cure
- Excellent Adhesion
- Excellent Abrasion Resistance
CONSIDERATIONS
- Allow material to rest for 15-20 minutes for viscosity adjustment.
- Application rate is no less than 250-275 square feet per gallon. Thicker films will show bubbling in the cured film.
COMPOSITION
EPOXY.COM PRODUCT #442 is a polyester resin/aliphatic polyisocyanate.
COLOR SELECTION
EPOXY.COM PRODUCT #442 is available in clear and pigmented colors. Gloss finish. For satin use Product #441.
ESD formulation available in clear or pigmented.
Epoxy.Epoxy.com # 442 is available in clear and pigmented colors below.
Click the picture
of color card at the side for a larger version of this picture of the
color chart.
Please note:
The picture to the right is a photographic reproduction
of the color card for this product. The photo reproduction process and
your monitor and/or printer will change these colors. This chart is to
give you an idea of the colors available and not intended for critical
color selections.
APPLICATION
SURFACE PREPARATION
Surface Preparation is the most critical portion of any successful resinous flooring system application. All substrates must be properly prepared as outlined in Epoxy.com Surface Preparation Procedures..
MIXING INSTRUCTIONS
- Mix only that amount of material that can be used in a two hour period. In hot weather, plan work for the cooler times of the day.
- If using less than full units, proportion the amounts carefully and mix for 2-3 minutes using a low speed drill, scraping the bottom and sides of the mixing vessel. DO NOT ADD WATER.
APPLICATION
- Apply Product #442 polyurethane at a spread rate of 275-300 square feet per gallon to achieve 2.0-2.5 mils dry. Thicker application may result in bubbling in the cured film.
- Recoat time is approximately 10 hours at 77°F.
- Keep a wet edge at all times.
- Apply Product #442 ESD at a spread rate of 160 square feet per gallon to achieve 5 mils dry.
- Use with adequate ventilation.
- Read material safety data sheet before using.
TECHNICAL DATA
| Mixing Ratio Clear | 4 Parts A to 1 Part B by Volume |
| Solids Content Clear | 43%, by Volume |
| Volatile Organic Content (VOC) | 0.10 pounds/gallon |
| Pot Life |
1 ½ - 2 hrs. @ 77°F, 1 Quart 45 minutes @ 95°F, 1 Quart |
| Viscosity After 15 Minutes @ 77°F | 500-600 cps. |
| Viscosity After 30 Minutes @ 77°F | 600 cps. |
Wait 15-20 minutes after mixing to start application. Viscosity will decrease with time.
DO NOT ADD WATER.
PERFORMANCE PROPERTIES
| Gloss, 60˚ - Clear | Gloss Finish |
| Tabor Abrasion,
1,000 gm. load, 1,000 cycles, CS-17 Wheel | 45 mg. loss |
| Impact Strength ASTM-D-2794 |
Direct 160 in. lbs.
Reverse 160 in. lbs. |
DRY TIME @ 77°F, 50% R.H.
| Dry to Touch | 6 hours |
| Recoat | 10 hours |
| Light Traffic | 16-24 hours |
| Full Cure | 4-5 days |
MAINTENANCE
After completing the application of EPOXY.COM PRODUCT #442 Urethane Coating/Sealer, the installer should provide the owner with maintenance instructions. EPOXY.COM PRODUCT #442 is easily cleaned with neutral soaps or detergents.
Proper mixing and installation are critical to the success of all products. See Installation Tips, Techdata, and (M)SDS for more details, or contact us with any questions.
321-206-1833 Customer Service – Ordering and Order Status
Katey Lambert-Fontaine – Vice President & Chief Operations Officer
katey@epoxy.com
352-533-2167 Technical Support
Norm Lambert – President & Technical Support Director
info@epoxy.com
Debby Lambert, Co-Founder and Strategic Planning
Website: www.epoxy.com
24-hour Hazmat Emergency Telephone Response Service: 1-800-633-8253
[Home] [Catalog of Products] [SDS] [Online Ordering Authorization Form]