|
||
| [Contact Us] | ||
Chemical Resistant Polyurethane Maintenance Coating
Excellent UV and Chemical Resistance
Epoxy.com Product #402
GENERAL DESCRIPTION
Epoxy.com PRODUCT #402 Chemical Resistant Polyurethane Coating is a two component chemical resistant polyurethane coating. The high gloss finish offers excellent abrasion resistance, chemical and stain resistance, and color retention.
Epoxy.com PRODUCT #402 Chemical Resistant Polyurethane Coating can be used equally well on vertical or horizontal surfaces. It is ideal for concrete floors and walls in warehouses, storage facilities, aircraft hangers, animal housing, and vehicle maintenance facilities.
Epoxy.com PRODUCT #402 Chemical Resistant Polyurethane Coating is not for use in California
ADVANTAGES
- Excellent Abrasion Resistance
- Excellent Chemical Resistance
- UV Resistant - means a long life even in direct sunlight
- Excellent Color Stability - Pigmented Version
- Clear Version Resists Ambering Even in the Brightest Sunlight
- Exterior and Interior Uses
- May be used on both Horizontal and Vertical Applications
Epoxy.com Product #402
Clear
Over Chip Flooring - Over Basement Room
Picture Courtesy of Matt Dekman
Used with Permission - All Rights Reserved
SURFACE PREPARATION
Surface must be clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, or mechanical abrasion. Remove water and dust from all surfaces with an oil-free blast immediately prior to application.
APPLICATION
Prime: For best bond to properly prepared surface, use Epoxy.com Product #899 Primer.
Body: Apply Epoxy.com PRODUCT #402 Chemical Resistant Polyurethane Coating with brush, roller (short napped), or squeegee followed with back rolling to get recommended thickness (3 mils DFT).
Finish: Apply top coat as required (minimum 3 mils DFT).
Epoxy.com PRODUCT #402 Chemical Resistant Polyurethane Coating is also available in the following forms:
- As a slip or skid resistant finish using a non-skid additive in the finish.
- As an electrostatic dissipating finish version - Epoxy.com Product #675
LIMITATIONS
Epoxy.com Product #402
Clear
Over Chip Flooring - On Outside Patio
Picture Courtesy of AA Permacoat
Used with Permission - All Rights Reserved
Surface to receive Epoxy.com PRODUCT #402 Chemical Resistant Polyurethane Coating must be dry. Minimum application temperature of 40°F (Contact Epoxy.com Technical Support for Low Temperature Cure). Maximum application temperature of 100°F. Avoid applications on surfaces without effective vapor barriers.
SAFETY PRECAUTIONS
Prolonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves.
CLEANING
All tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent.
Physical Properties |
|
| Color |
Standard colors for this product are:
Clear (satin and gloss), White #001, Light Gray #100, and Dark Gray. Other standard colors are available with a 30 gallon minimum ordere |
| Gloss, 60°F | 85-100 |
| Mix Ratio | 2Ato 1B by volume |
| Pot Life | 30-40 minutes @ 70°F |
| VOC | 405 gm/liter |
| Solids Content, % volume | 56.0 |
| Coverage | 300 ft2/gal @ 3 mils DFT |
DRY TIME |
|
| 10-20 mil film | 1O~14 hrs |
| Light Traffic | 16 hrs |
|
Ultimate Cure @ 74°F @50°F |
5 days 14davs |
CHEMICAL RESISTANCE |
|||
REAGENT |
Rating |
REAGENT |
Rating |
| Acetic Acid-5% | L | Iodine | R |
| Acetone | L | Lactic Acid-15% | R |
| Betadine | R | Methyl Ethyl Ketone | L |
| Bleach | L | Nitric Acid-10% | R |
| Citric Acid-30% | R | Skydrol | R |
| Crude Oil | R | Sodium Hydroxid-50% | R |
| Diesel Fuel | R | Sulfuric Acid-20% | R |
| Ethylene Glycol | R | Toluene | R |
| Fafty Acids | L | Urea | R |
| Gasoline | R | Vinegar | L |
| Hydrochloric Acid-15% | R | Xylene | R |
|
R= Recommended for continuous Service L=Limited recommendation, occasional spills |
|||
PERFORMANCE PROPERTIES |
|
| Adhesion to concrete ACI Committee 403 | 200 psi (concrete fails) |
| Abrasion Resistance ASTM-C501 |
30-40 mg loss (CS-17 wheel, 1 kg load, 1000 cycles) |
| Service Temperature MIL- D-3134F | 160°F (immersion) 250°F (dry heat) |
| Impact Resistance MTI-D-3134F ss 4.7.5 | Withstands 16ft./lbs. no cracking, delamination or chipping |
| Elevated Temperature Resistance MIL-D-3134F ss 4.7.3 | No slip or flow at required temperatures at 158°F |
| Water Absorption (24. hr. immersion) ASTM-D-670-63 | 0.10% maximum |
| Hardness ASTM D3363 | 2H± |
BLOG POSTS & NEWS
You can find more information on Polyurethane Products, and many of our other products at news.epoxy.com.
Download this file in Adobe Acrobat format for formal presentation.
Proper mixing and installation is critical to the optimal success of all products. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have.
For more information please contact:
Epoxy.com
A Division of Epoxy Systems, Inc
A Vermont Corporation
USA
We have products that have passed the test of time as well as the best new Systems available today.
Since 1980 - Over 45 years of the highest quality products
Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time)
Closed for lunch from 12Noon to 1PM
321-206-1833 Customer Service - Ordering and Order Status
Katey Lambert-Fontaine - Vice President & Chief Operations Officer
katey@epoxy.com
352-533-2167 Technical Support
Norm Lambert - President & Technical Support Director
info@epoxy.com
Debby Lambert, Co-Founder and Strategic Planning
Website: www.epoxy.com
24 hour Hazmat Emergency Telephone Response Service - 1-800-633-8253
[Home] [Catalog of Products] [MSDS in Acrobat Format] [Online Ordering Authorization Form]