Epoxy Since 1980

Epoxy.com Product #315TOP Chemical Resistant Epoxy Resin Flooring / Floor Resurfacing System for Seamless Epoxy Chip Flooring is a two component, seamless 100% solids clear epoxy flooring / floor resurfacing system with High Chemical Resistance. The epoxy may be applied as a coating, or combined as a top coating for Epoxy.com Chip Flooring to produce a durable, easy to maintain floor, on both new and old surfaces.

Although Epoxy.com Product #315TOP Epoxy Chemical Resistant Flooring Resurfacing System for Seamless Chip Flooring is primarily used as a flooring and mortar resin is one of Epoxy.com's most versatile products. It is also commonly used for resealing epoxy bonded stone, to seal acid stained floors and as a carbon composite and fiberglass layup resin.

ADVANTAGES

LOW ODOR
CHEMICAL RESISTANT
STRONG YET RESILIENT
VARIABLE SURFACES FROM NON-SLIP TO SMOOTH
ABRASION RESISTANT
ZERO VOCs - MEETS EVEN THE STRICTIST LOW VOC REQUIRMENTS
MEETS USDA STANDARD FOR USE IN FOOD HANDLING APPLICATIONS

SURFACE PREPARATION

Surface to receive Epoxy.com Product #315TOP Epoxy Chemical Resistant Flooring Resurfacing System for Seamless Epoxy Chip Flooring must be clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, mechanical abrasion. If acid etching is used follow with abrasive or mechanical abrasion. Remove water and dust from all surfaces with an oil free blast, or vacuum, immediately prior to application. See Epoxy.com Surface Preparation Guide for more details.

MIXING INSTRUCTIONS

Temperature of Epoxy.com Product #315TOP Epoxy Chemical Resistant Flooring Resurfacing System for Seamless Epoxy Chip Flooring must be 65 degrees F or above at time of mixing. Stir each component separately before blending. Mix two parts by volume of Part A with one part by volume of Part B for three minutes with a low speed electric drill motor equipped with a mixing paddle.

APPLICATION

Epoxy.com Product #315TOP Epoxy Chemical Resistant Flooring Resurfacing System for Seamless Epoxy Chip Flooring can be applied with brush, roller, trowel, airless sprayer or squeegee. Apply a coat of #15 to surface to be finished, doing only a small area at a time. If anti-skid is required, (while epoxy is still wet) it may be broadcast with aggregate. This can be done by hand or mechanical means. Make sure that the entire surface is completely covered (no shiny spots visible). Allow them to dry. Then sweep off excess aggregate. Sand surface (if required) to desired texture. If broadcast with sand a top-coat over the entire surface.. For more information on installation please see:

New concrete to receive Epoxy.com Product #315 Epoxy Chemical Resistant Flooring Resurfacing System for Seamless Epoxy Chip Flooring should be at least 28 days old. Temperature of substrate must be above 55 degrees F. DO NOT thin. For indoor use (except when used to seal Epoxy.com Product #17 or similar product) contact Epoxy.com for technical assistance.

OPTIONAL FEATURES

SAFETY PRECAUTIONS

Prolonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves.

CLEANING

All tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent.

APPLICATION PROPERTIES @77°F
Mix Ratio	2:1 By Volume
Viscosity (mixed)	450 CPS
Pot Life (200 gr.)	30 minutes
Cure Time (Walk-on Traffic)	24 hours
Cure Time (Truck Traffic)	48 Hours
Final Cure	7 Days
VOC Content	0.0 lbs per Gallon (Zero VOC)
Packaging (unit size)	15 gal. Units (5 gal pails)

PHYSICAL PROPERTIES (neat)
Bond Strength (ASTM C-882)	2110 PSI
Flexural Strength (ASTM D-2240)	6075 PSI (7 days)
Compressive Strength (ASTM D-695)	9910
Absorption (ASTM D-570)	0.6%
Thermal Shock	40 Hr. @10° F., 3 Min. @ 212° F. Shock Water @ 33° F.
Hardness (Shore D)	65 @ 24 Hours, 75 @ 7 days

Estimating Coverage

For a 1/8 inch double broadcast system you can use the material calculator for Epoxy.com Product #15.

CHEMICAL RESISTANT CHART
Reagent	CHEMICAL TEST TIME MONTHS
Reagent	1	3	6	9	12
WATER, DISTILLED	+	+	+	+	+
SEAWATER	+	+	+	+	+
SULFURIC ACID, 10%	+	+	+	S	S
SULFURIC ACID, 30%	+	+	S	-	-
SULFURIC ACID, 70%	+	S	-	-	-
HYDROCHLORIC ACID, 10%	+	+	+	+	+
HYDROCHLORIC ACID, 20%	+	+	+	+	+
HYDROCHLORIC ACID, 36%	+	+	+	+	+
HYDROCHLORIC VAPOR	+	+	+	+	+
ACETIC ACID, 5%	+	+	-	-	-
ACETIC ACID, 10%	-	-	-	-	-
AMMONIUM HYDROXIDE, 10%	+	+	S	S	-
AMMONIUM HYDROXIDE, 25%	+	S	-	-	-
SODIUM HYDROXIDE, 20%	+	+	+	+	+
ACETONE	-	-	-	-	-
BUTANONE	-	-	-	-	-
BUTYL ACETATE	+	+	S	S	S
DIACETONE ALCOHOL	+	+	+	+	+
CELLOSOLVE	S	S	S	S	S
ETHANOL, 50%	+	+	+	-	-
ETHANOL, 96%	-	-	-	-	-
OCTANOL	+	+	+	+	+
XYLENE	+	+	+	+	+
TOLUENE	+	+	+	+	+
BENZENE	+	+	S	S	S
SKYDROL	+	+	+	+	+
TRICHLOROETHYLENE E	+	+	S	S	S
CRUDE OIL	+	+	+	+	+
GASOLINE, 98 OCTANE	+	+	+	+	+
ACETAL GLACIAL	-	-	-	-	-
CITRIC 10%	+	+	+	+	+
CITRIC 50%	+	+	+	+	+
FATTY ACID (LINSEED)	+	+	+	+	+
LACTIC (DAIRY PRODUCTS)	+	+	+	+	+
NITRIC 10%	+	-	-	-	-
NITRIC 20%	+	-	-	-	-
NITRIC 30%	+	-	-	-	-
PHOSPHORIC	-	-	-	-
ALLYL CHLORIDE	+	S	S	S	S
CARBON TETRACHLORIDE	+	+	+	+	+
DIETHYLENE TRIAMINE	-	-	-	-	-
ETHYL ALCOHOL	-	-	-	-	-
ETHYLENE DIAMINE	-	-	-	-	-
FORMALDEHYDE	-	-	-	-	-
METHYL ETHYL KETONE	S	-	-	-	-
ISOPROPYL ALCOHOL	+	+	+	+	+
METHYL ISOBUTYL CARBINOL	+	+	+	+	+
METHYL ISOBUTYL KETONE	S	S	S	S	S
MINERAL SPIRITS	+	+	+	+	+
DETERGENTS ANIONIC 2%	+	+	+	+	+
CALCIUM HYPOCHLORITE 5%	+	+	+	+	+
SODIUM CHLORITE 25%	+	-	-	-	-
SODIUM HYPOCHLORITE 5%	+	-	-	-	-
STAIN RESISTANCE
BUTTER	+	+	+	+	+
CITRUS JUICES	+	+	+	+	+
COFFEE	+	+	+	+	+
COLA	+	+	+	+	+
GREASE	+	+	+	+	+
HAIR TONIC	+	+	+	+	+
INK	+	+	+	+	+
LARD	+	+	+	+	+
LIPSTICK	+	+	+	+	+
LIQUOR	+	+	+	+	+
MILK	+	+	+	+	+
MINERAL OIL	+	+	+	+	+
MUSTARD	+	+	+	+	+
VINEGAR	+	+	+	+	+
SANDBLASTED STEEL PANELS, COATED WITH AN AVERAGE. OF 14 MIL FILM THICKNESS, IMMERSED IN THE VARIOUS MATERIAL FOR UP TO ONE YEAR + = Resistant S= Softened -= Attacked

Material Certification of LEED Requirements

Epoxy.com a division of Epoxy Systems, Inc. certifies that Epoxy.com Product #15 meets or exceeds LEED requirements as summarized below:

LEED Credit IE 4.2:

Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to LEED IEQ 402 Indoor Emitting Materials Credit. Refer to the individual product component technical data sheets and MSDS for further information.

Certificate or Origin

This product is made and or assembled in the USA.

Chemical Resistant Chip Flooring Top Coating

Seamless Resurfacing System

Epoxy.com Product #315TOP

Best Clear Epoxy Material for Installing Seamless Epoxy Chip Flooring

For Chip Flooring Systems and for Sealing Acid Stained Concrete

GENERAL DESCRIPTION

APPLICATIONS

ADVANTAGES

SURFACE PREPARATION

MIXING INSTRUCTIONS

APPLICATION

OPTIONAL FEATURES

SAFETY PRECAUTIONS

CLEANING

APPLICATION PROPERTIES @77°F

PHYSICAL PROPERTIES (neat)

Estimating Coverage

CHEMICAL RESISTANT CHART

Reagent

STAIN RESISTANCE

Material Certification of LEED Requirements

LEED Credit IE 4.2:

Certificate or Origin